From: Willem van der Walt <wvdwalt@csir.co.za>
To: "Speakup is a screen review system for Linux." <speakup@braille.uwo.ca>
Subject: Re: help with Fedora
Date: Thu, 28 Jul 2005 15:33:30 +0200 (SAST) [thread overview]
Message-ID: <Pine.LNX.4.62.0507281532520.31376@localhost.localdomain> (raw)
In-Reply-To: <6.2.3.4.0.20050728073840.03905238@pop3.citlink.net>
Yes, it is linux rescue.
Regards, Willem
On Thu, 28 Jul 2005, Scott Berry wrote:
> Okay thanks for the help I will check that.
>
> Is there a special way to get in to the rescue process? Like typing "linux
> rescue" on the first disk?
>
>
>
> At 01:44 AM 7/28/2005, you wrote:
>
>> Hi,
>> I would try going into rescue mode with fc3 and run fdisk to have a look at
>> the disk. Once in rescue mode, fdisk /dev/hda should go in the p command
>> then should show the partitions. If that give a simelar error, I would
>> start checking the hardware.
>> Make sure the existing linux on the hard drive still boots etc.
>> A thing that i assume you have checked is that the drive is actually
>> connected to the first primary IDE controler and therefore is called hda.
>> I have had machines where the only drive was connected to the second IDE
>> controler's master making it hdc.
>> HTH Willem
>>
>>
>> On Wed, 27 Jul 2005, Scott Berry wrote:
>>
>>> Hello list,
>>>
>>> I am having a problem with a Toshiba laptop. When I go to install Fedora
>>> I get as far as the partitioning. I wanted to do an automatic when I
>>> tried this however, it gave an error like this: "i/o error not able to
>>> read /dev/hda." I thought it was because there is another Linux
>>> distribution on the system but I went in and did a manual but the New Edit
>>> and Delete would not come up for some reason. Can some one give me some
>>> advice as how I might go about fixing this? It is Fedora 3. I am
>>> currently using sighted assistance because my notebook does not have a
>>> serial port so I will have to set up Speakup for software speech. Thanks
>>> much.
>>>
>>> Scott
>>>
>>> _______________________________________________
>>> Speakup mailing list
>>> Speakup@braille.uwo.ca
>>> http://speech.braille.uwo.ca/mailman/listinfo/speakup
>>
>> --
>> This message is subject to the CSIR's copyright, terms and conditions and
>> e-mail legal notice. Views expressed herein do not necessarily represent
>> the
>> views of the CSIR.
>> CSIR E-mail Legal Notice
>> http://mail.csir.co.za/CSIR_eMail_Legal_Notice.html
>> CSIR Copyright, Terms and Conditions
>> http://mail.csir.co.za/CSIR_Copyright.html
>> For electronic copies of the CSIR Copyright, Terms and Conditions and the
>> CSIR
>> Legal Notice send a blank message with REQUEST LEGAL in the subject line to
>> HelpDesk@csir.co.za.
>>
>>
>> This message has been scanned for viruses and dangerous content by
>> MailScanner, and is believed to be clean. MailScanner thanks Transtec
>> Computers for their support.
>>
>>
>> _______________________________________________
>> Speakup mailing list
>> Speakup@braille.uwo.ca
>> http://speech.braille.uwo.ca/mailman/listinfo/speakup
>>
>
>
> _______________________________________________
> Speakup mailing list
> Speakup@braille.uwo.ca
> http://speech.braille.uwo.ca/mailman/listinfo/speakup
>
--
This message is subject to the CSIR's copyright, terms and conditions and
e-mail legal notice. Views expressed herein do not necessarily represent the
views of the CSIR.
CSIR E-mail Legal Notice
http://mail.csir.co.za/CSIR_eMail_Legal_Notice.html
CSIR Copyright, Terms and Conditions
http://mail.csir.co.za/CSIR_Copyright.html
For electronic copies of the CSIR Copyright, Terms and Conditions and the CSIR
Legal Notice send a blank message with REQUEST LEGAL in the subject line to
HelpDesk@csir.co.za.
This message has been scanned for viruses and dangerous content by MailScanner,
and is believed to be clean. MailScanner thanks Transtec Computers for their support.
prev parent reply other threads:[~ UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
Scott Berry
` Willem van der Walt
` Scott Berry
` Willem van der Walt [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Pine.LNX.4.62.0507281532520.31376@localhost.localdomain \
--to=wvdwalt@csir.co.za \
--cc=speakup@braille.uwo.ca \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).