From mboxrd@z Thu Jan 1 00:00:00 1970 Received: from pc1-norb6-0-cust216.nth.cable.ntl.com ([80.4.50.216] helo=debian.linux ident=mail) by speech.braille.uwo.ca with esmtp (Exim 3.35 #1 (Debian)) id 174Rde-0006RB-00 for ; Sun, 05 May 2002 15:25:42 -0400 Received: from localhost ([127.0.0.1] helo=gena-j.net ident=gena) by debian.linux with esmtp (Exim 3.35 #1 (Debian)) id 174Rdi-0000Lk-00 for ; Sun, 05 May 2002 20:25:46 +0100 To: speakup@braille.uwo.ca Subject: Re: New Kernel with Speakup and ZIPSPEAK In-reply-to: Your message of 05 May 2002 20:30:00 +0100. <8OIuTp0bJVB@0256597511.t-online.de> Date: Sun, 05 May 2002 20:25:46 +0100 From: 'Georgina' Message-Id: Sender: speakup-admin@braille.uwo.ca Errors-To: speakup-admin@braille.uwo.ca X-BeenThere: speakup@braille.uwo.ca X-Mailman-Version: 2.0.8 Precedence: bulk Reply-To: speakup@braille.uwo.ca List-Help: List-Post: List-Subscribe: , List-Id: Speakup is a screen review system for Linux. List-Unsubscribe: , List-Archive: Hi I can't remember if the default value is for MS DOS file system supported or not. I thought that it was. Can you run make menuconfig? This is a lot easier to quickly look and make changes. If this was the case, I thought that the error message would of stated such. Could it be an error from incorrectly stating the root device on the loadlin commandline. Although, I guess that it hasn't been changed. But double check that your loadlin line looks like something like this: loadlin.exe \linux\vmlinuz-new root=/dev/hda1 ro HTH Gena Blindness Advocacy and Self Help Online www.bashonline.org >Hello, > >i use zipspeak ud want to compile a nwe kernel, so that all my hardware >ist installed. >I have downloaded the kernel 2.4.188 an speakup-1.00. >Then i have done the following steps: > >cd /usr/src >rm -r speakup* >rm -r linux*tar xzf speakup-1.00.tgz >tar xzf linux-2.4.18.tgz >cd speakup-1.00 >./install >cd ../linux >make mrproper >make config (i have only done the steps for speakup) >make dep >make bzImage >mv /vmlinuz /vmlinuz.old >cp arch/i386/boot/bzImage /vmlinuz >cp System.map /boot/system.map >shutdown -r now > >I load linux with loadlin and not with lilo. lilo ist not on my harddisk. >I have not become any errors during the compilation of the kernel. At the >end was only a warning: kernel ist to great for a floppydisk > >After rebooting i start linux with linux.bat form the dos-prompt. My apolo >speaks kernel 2.4.18 and so on. My hardware ist detected and then comes a >message: > >can not mount /root fs >Kernel panik > >What can i do or does this kernel not work with Zipslack (zipslack)? > >Thanks. >Dietmar > >_______________________________________________ >Speakup mailing list >Speakup@braille.uwo.ca >http://speech.braille.uwo.ca/mailman/listinfo/speakup