Re: switching from amd to p3

["Doug Sutherland" <doug@proficio.ca>]

Tyler said:
The cables are ok. do I just move it around on the cable?

The disk boot error is severe, and I would think that needs
to be solved even if you want to do a network boot. It is
hard to say without trying some things, but I would check

Is the IDE cable inserted the right way up in the drive.
Some drives will only let you insert it one way, others
will let you do it upside down.

Is the IDE cable inserted into the first IDE controller
port on motherboard. Best way to check is in BIOS,
you should see the drive as master.

Is the power cable inserted in the drive.

If more than one drive on same cable, one must be
set as master, one as slave, done by jumpers using
the label on drive as guide. As suggested before if
there already is another drive, try removing it and
boot with just the newly setup drive.

If all the physical connections seem okay, the next
thing I would do is boot from a CD or floppy and
do what I said before, at the boot prompt enter

kernel-name root=/dev/hda1 noinitrd ro

where kernel-name is the name of kernel on the
removable media, and the kernel is a "bare" one,
not specific to hardware, ie its 386 and generic
controllers. On slackware its called bare.i but
there should be an equivalent on debian. And
make sure the root= points to the right drive
letter and number of the partition with the root
file system.

You could also try loading a generic kernel on
the AMD, making sure it boots there, then
moving the kernel over. You'll have to check
the debian docs to find out which kernel to use.
I haven't use debian in a while.

> How hard are these floppies to get for deb?

http://http.us.debian.org/debian/dists/etch/main/installer-i386/current//images/floppy/
http://www.debian.org/releases/stable/i386/ch04s03.html.en

  -- Doug







> Thanks,
> Thanks,
> ~~TheCreator~~
> [My programs don't have bugs; just randomly added features]
> msn:
> compgeek13@gmail.com
> aim: st8amnd2005
> skype: st8amnd127
> vertigo head coder
> web: tysdomain.com
> ----- Original Message ----- 
> From: "Doug Sutherland" <doug@proficio.ca>
> To: "Speakup is a screen review system for Linux."
<speakup@braille.uwo.ca>
> Sent: Saturday, June 16, 2007 7:03 PM
> Subject: Re: switching from amd to p3
>
>
> > If you're getting disk boot failure then probably something
> > is not right with the physical connection, the IDE cable or
> > possibly the BIOS needs to be tweaked to recognize the
> > hard drive. If there is more than one drive in the system
> > make sure the one you are moving in is on the first IDE
> > port so it's drive A, also make sure there are no conflicts
> > if you have two drives in there ie make sure one is set as
> > master by jumper and the other is set as slave.
> >
> > I think you can get disk boot error even if there is no disk
> > at all, so start by checking the physical connections and
> > jumpering of drives.
> >
> > The other thing that sometimes happens when moving
> > drives around is that what was drive a becomes drive
> > c for example, in that case you will get a kernel panic
> > with message stating no root file system found. If this
> > happens, then the other procedure I mentioned will
> > work, booting from cdrom or floppy, loading the
> > kernel from removable storage with the boot param
> > root= pointing to the proper location of root file system
> > (follow that with noinitrd ro) and then once booted you
> > can rebuild the kernel and update the bootloader.
> >
> > What you are doing is definitely possible, I have done
> > it many times, building an entire system on on PC then
> > then moving the drive to a mobile system.
> >
> >   -- Doug
> >
> > _______________________________________________
> > Speakup mailing list
> > Speakup@braille.uwo.ca
> > http://speech.braille.uwo.ca/mailman/listinfo/speakup
>
> _______________________________________________
> Speakup mailing list
> Speakup@braille.uwo.ca
> http://speech.braille.uwo.ca/mailman/listinfo/speakup